Products

 

(UN)Designs Rad Bracket

Description:

Have you ever needed another radiator but couldn’t find a place to put it. Now you can put those extra front bays to good use. Designed to allow you to install any radiator that will fit width wise in any 5.25 bay. There are numerous different ways to mount the brackets allowing virtually any radiator to fit. This could open up a whole new way of mounting your radiator.

Features:

• Allows virtually any radiator to be mounted in a 5.25 bay
• Multiple ways to mount brackets ensure proper mounting
• Comes with mounting screws
• Powder Coated Black Finish!

 

 

 

(UN)Designs Infinite Bracket

(Horizontal and Vertical)

Infinite [640x480]

Description:

The Infinite Horizontal (formerly the Absolute) and Infinite Vertical (formerly the 3G) are the newest members to the (UN) lineup. The only limit to your mounting requirements really is your imagination.  You now have infinite ways to mount your pumps, reservoirs, or whatever else you can think of. By having the pump swivel around the bracket, you can help eliminate kinks in the tubing which allows for more possibilities for pump mounting.  These can be used for much more than pumps though. Simple to install, comes with all the hardware to mount the bracket. Requires the stock rubber grommets for the DDC pumps and the stock mounting screws for the D5.

Features:

• Application: Laing DDC pump (aka Swiftech MCP350/MCP355), Danger Den DDC and DDC 3.2, Laing D4/D5 pump (aka Swiftech MCP650/MCP655(-B), Danger Den D4/D5 Vario and Basic, D-Tek D4/D5 Vario and Basic, most aftermarket tops.
• Increased airflow around the pump- especially in the DDC series
Everything is slotted now so it’s possible to make micro adjustment when mounting pumps, etc.
• Helps to reduce vibration
There is a new swivel point on the base which rotates the arm 360 degrees allowing even more   adjustments.
Horizontal version is lower than the 3G to allow more room to mount in the bottom of cases
• Powder Coated Black Finish

 

 

(UN)Designs Z2 & Z3 Brackets

 

 
Description:
Have you ever wanted to mount something to a 120mm or 140mm fan but didn’t have the right hardware, well now you do! With the New Z2 and Z3 you can mount not only any (UN)Designs bracket but a wide variety of items. This could open up a whole new way of mounting your accessories. The Z-Bracket Features:

• Allows airflow over your accessories to help reduce heat, especially good for pumps
• Allows multiple mounting locations that would not normally be accessible
• Fits 120mm (Z2) and 140mm (Z3) fans
• Can be used with any (UN)Designs Brackets, old or new

 

 

 

 

(UN)Designs X Bracket Horizontal

X Bracket- Horizontal

Description:

So you just spent all that money on that fancy new SSD and now your gonna hide it in an enclosure or stick it with some velcro to the side of your case?
The X bracket is designed to show off that new SSD and give it a solid mount.
There are two flavors, a horizontal mount and a vertical mount. Both can hold up to two drives.

Features:

• Allows a solid mount
• Can be mounted virtually anywhere
• Comes with mounting hardware
• Powder Coated Black Finish!

(UN)Designs X Bracket Vertical

X Bracket- Vertical

Description:

So you just spent all that money on that fancy new SSD and now your gonna hide it in an enclosure or stick it with some velcro to the side of your case?
The X bracket is designed to show off that new SSD and give it a solid mount.
There are two flavors, a horizontal mount and a vertical mount. Both can hold up to two drives.

Features:

• Allows a solid mount
• Can be mounted virtually anywhere
• Comes with mounting hardware
• Powder Coated Black Finish!

(UN)Designs “Brick Road”

4 x 120mm Quad Rad Grill – Black

Product Details:

(UN)Designs Quad Grill for 4 x 120mm Fans!

This classic Quad Grill from (UN) Designs is designed for good airflow as well as good looks. Made from steel for increased strength.

Features:

  • Fits standard 15mm spacing.
  • Made of durable steel – powder coated black
  • Has four mounting holes to attach to the top of the case

Specifications:

  • Machined Steel with Hard Black Powder Coat

******DISCONTINUED ITEMS******

 

(UN)Designs Absolute Pump Bracket Rev.3

Discontinued

(for Laing D5/DDC pump)


Instructions: Correct Mounting Technique
Description:

With the Absolute Rev.3 the only limit really is your imagination.  A new slot allows you to mount a variety of aftermarket tops for the D5 as well as anything else you can bolt to it. By having the pump swivel around the bracket, you can help eliminate kinks in the tubing which allows for more possibilities for pump mounting.  Simple to install, comes with all the hardware to mount your pump. (Requires use of the stock rubber grommets for the DDC pumps)
Features:
• Application: Laing DDC pump (aka Swiftech MCP350/MCP355), Danger Den DDC and DDC 3.2, Laing D4/D5 pump (aka Swiftech MCP650/MCP655(-B), Danger Den D4/D5 Vario and Basic, D-Tek D4/D5 Vario and Basic, most aftermarket tops.
• Increased airflow around the pump- especially in the DDC series
• Swivel Bracket allows the pump to be mounted in almost any direction
• Helps to reduce vibration
• Extra mounting holes allow for height adjustment
• Sleek bracket design improves the overall look of the pump
• Powder Coated Black Finish

(UN)Designs 3G Pump Bracket

Discontinued

(for Laing D5/DDC pump)


Instructions: Correct Mounting Technique
Description:
With the 3G Rev.2 the only limit really is your imagination.  A new slot allows you to mount a variety of aftermarket tops for the D5 as well as anything else you can bolt to it. By having the pump swivel around the bracket, you can help eliminate kinks in the tubing which allows for more possibilities for pump mounting.  Simple to install, comes with all the hardware to mount your pump. (Requires use of the stock rubber grommets for the DDC pumps)
Features:
• Application: Laing DDC pump (aka Swiftech MCP350/MCP355), Danger Den DDC and DDC 3.2, Laing D4/D5 pump (aka Swiftech MCP650/MCP655(-B), Danger Den D4/D5 Vario and Basic, D-Tek D4/D5 Vario and Basic
• Swivel Bracket allows the pump to be mounted in almost any direction
• Helps to reduce vibration
• Extra mounting holes allow for height adjustment
• Sleek bracket design improves the overall look of the pump
• Powder Coated Black Finish

(UN)Designs Z-Bracket

Discontinued


Description:
Have you ever wanted to mount your DDC or D4/D5 in your case but couldn’t find a suitable place? With the New Z-Bracket you can mount the (UN)Designs 3G or Absolute brackets wherever there is a 120mm fan. This could open up a whole new way of mounting your pump. The Z-Bracket is compatible with any (UN)Designs brackets including the older revisions.

Features:
• Allows airflow over the Pump to help reduce heat
• Allows multiple mounting locations that would not normally be accessible
• Fits 120mm fans
• Can be used with any (UN)Designs Brackets, old or new
• Comes with fans screws too!

(UN)Designs 360 Pump Bracket Rev.2

Discontinued

(for Laing D4/D5 pump)


Description:
Have you ever tried to mount your Laing D4/D5 pump with the stock bracket and realized that you couldn’t do it? Well guess what, now you can mount your D4/D5 pump wherever you want too! With the 360 pump bracket the only limit is your imagination. By having the pump swivel around the bracket, you can help eliminate kinks in the tubing. Simple to install, you can use all of the stock hardware that comes with your pump. Comes preassembled and ready to use.

Features:
• Application: Laing D4/D5 pump (aka Swiftech MCP650/MCP655(-B), Danger Den D4/D5 Vario and Basic, D-Tek D4/D5 Vario and Basic
• Swivel Bracket allows the pump to be mounted in almost any direction
• Extra mounting holes allow for height adjustment
• Sleek bracket design improves the overall look of the pump

(UN)Designs Rad Spacers

Discontinued

Description:
With the Rad spacer you can cover the gap between two radiators and finally hide all those unsightly wires. Made from anodized aluminum these spacers will add that finishing touch. They also make a great place to mount your case lighting. There are several different models depending on what spacing is required and what type of radiators you are using.

Features:
• Fits standard Swiftech spacing
• Helps to hide wires
• Extra mounting location for case lighting
• Gives that clean finished look
• Anodized black aluminum
or Powder Coated Steel